SYSTEMS ECO-FRIENDLY DESIGN FOR INNOVATIVE PROCESSES
Anno accademico 2016/2017 - 2° anno
Docente: Giovanni GRASSO
Crediti: 9
SSD: ING-IND/14 - PROGETTAZIONE MECCANICA E COSTRUZIONE DI MACCHINE
Organizzazione didattica: 225 ore d'impegno totale, 171 di studio individuale, 54 di lezione frontale
Semestre: 2°
Crediti: 9
SSD: ING-IND/14 - PROGETTAZIONE MECCANICA E COSTRUZIONE DI MACCHINE
Organizzazione didattica: 225 ore d'impegno totale, 171 di studio individuale, 54 di lezione frontale
Semestre: 2°
Prerequisiti richiesti
Propedeuticità del piano di studi
Frequenza lezioni
Le lezioni si svolgeranno trisettimanalmente nel secondo semestre del secondo anno, verranno svolti, inoltre, esercizi di calcolo e progetto bisettimanalmente
Programmazione del corso
* | Argomenti | Riferimenti testi | |
---|---|---|---|
1 | * | Introduction to the course, Techical data of our Project, Principal Components of Implant analisyis | |
2 | * | Enegrtic Dimensioning of the T.C. the Reactor, the Flash, the Silos, etc | |
3 | * | Design and calculation of the Reactor | |
4 | * | WHOLER CURVE, SMITH-GOODMAN DIAGRAM, | |
5 | * | Hardness, Resilience, Test of Resilience, | |
6 | * | REACTOR THERMAL CALCULATION, THERMAL GENERATOR CALCULATION | |
7 | * | Verification of Reactor and Generator components | |
8 | * | Viscoelastic Theory | |
9 | * | Law of Fatique Propagation, Propagation Limit, Lawof WOLKER, CRACK CLOSURE, FATIGUE CRACK CLOSURE | |
10 | * | Creep Theory, Energetic approch, Fact k | |
11 | * | Steam line calculing and water treatment | |
12 | * | Charaterization of Materials, Gasket and Flanges under creep theory | |
13 | * | Creep calculation under Fatique stress | |
14 | * | Shells Theory, Membrane theory, (ex Cylinder, Cone, Sphere) | |
15 | * | P&I (Piping and Instrumentation Diagram o Process and Instrumentation Diagram) of implant Design | |
16 | * | Toroid-Spheric Vessel, Plates with axial symmetry, Instability of section under external pressure | |
17 | * | Membrane Stress distribution | |
18 | * | Logic Control : Implant definitions | |
19 | * | Locic Control: Water Treatmenrt, Thermal Power Unit | |
20 | * | Logic Control: Clean lines and Product delivery | |
21 | * | Logic Control:: Tests | |
22 | * | Secondary Stress on low thickness Vessels | |
23 | * | Verification on Logic Control of any Process Line | |
24 | * | High Thickness Vessels Calculation | |
25 | * | Complance Verifications between P&I and Logic Control | |
26 | * | Verifications Tests |
* Conoscenze minime irrinunciabili per il superamento dell'esame.
N.B. La conoscenza degli argomenti contrassegnati con l'asterisco è condizione necessaria ma non sufficiente per il superamento dell'esame. Rispondere in maniera sufficiente o anche più che sufficiente alle domande su tali argomenti non assicura, pertanto, il superamento dell'esame.
N.B. La conoscenza degli argomenti contrassegnati con l'asterisco è condizione necessaria ma non sufficiente per il superamento dell'esame. Rispondere in maniera sufficiente o anche più che sufficiente alle domande su tali argomenti non assicura, pertanto, il superamento dell'esame.
Verifica dell'apprendimento
Modalità di verifica dell'apprendimento
verifica del progetto e colloquio orale
Esempi di domande e/o esercizi frequenti
Tipi di propagazione della cricca,
diagrammi di fatica
calcolo flange
calcolo gusci sottili e di forte spessore,